Print

PTB111-20KA


Payload Capacity: 22,400#
GVWR:  26,000#

Length Adjustments:  24’  /  31’  /  38’
Overall Width:  95”
Bolster Height:  42”

22,500 lbs. Single Straight Axle
Oil Bath Hubs, 10 Studs
Air Brakes with Auto Slack Adjusters
ABS equipped and spring brakes
Adjustable Spring Pads for Wheel Alignment
Reinforced Spring Hangers with 3” Structural C-Channel Crossmembers
(4) Four - 255/70R 22.5 Tires
(4) Four - 22.5 10 bolt dual wheels
Pair - Mud Flaps

Front Bolster:  95" Wide Double C-Channel Front Bolster with 21" Stanchions
Center Bolster:  95”W Fixed 5” Double C-Channel Construction with 21” Stanchions
Rear Bolster:  95”W Fixed 5” Double C-Channel Construction with 21” Stanchions
Stanchions:  (4) four - 21” Lever Lock, Sliding & Removable
(4) four - Heavy Duty Ratchet Type Winch Binders with Breaker Bar
(4) four - 15’ L x 4” W x 12000 lbs. Nylon Straps

8” x 4” x 1/4" Wall Extendable Tongue with Extension Assist Roller and replaceable UHMW-PE Wear Pads
6-Position Adjustable Hitch Plate
2 1/2" Lunette Eye, 35000 lbs. Capacity
3/8” x 36”L Galvanized Safety Chains with Safety Hook and Anchor Shackle
7” Structural C-Channel A-Frame
12,000# Heavy duty drop leg jack

7” x 4” Tubular Steel Frame
10” x 6” Receiver Tube
7” x 4 “ Tubular Steel Crossmembers Under Rear Bolster
3” Structural C-Channel Crossmembers
Fabricated 1/8” Steel Diamond Tread Plate Fender Construction
Reinforced with 3” Structural C-Channel at Front and Rear of Fender
12 Gauge Steel Floor in between the center and rear bolsters

*Aluminum Under Body Tool Box: 18" x 18" x 48" with stainless steel "T" latches

ICC & DOT Approved LED Lights
Sealed Beam Rubber Mounted Stop, Turn, Tail and Marker Lights
S.O. Cable Wiring Loom, Clamped on 16” Centers with Rubber Lined Clamps
Wiring Loom Terminated in Junction Boxes
Connections Soldered and Sealed with Heat Shrink Tubing
Internal Wiring and air lines in Tongue, Plug Receptacle Located at Each Pinnable Location, Eliminates Coil Cord
7 way tractor trailer receptacle mounted on front of tongue for coil jumper cord to connect the truck to trailer
6-Way Aluminum Die Cast Plug (Truck Side) in Rear Butt Tube for Light Bar Hook-Up
Breakaway Kit with Sealed Lead Acid Battery & Trickle Charger

Includes (2) oval rubber mounted sealed beam lights (stop turn and tail); (3) center ID marker lights and two side marker lights.  Light bar is attached to the pole with an adjustable ¼" chain and wingnut.  Standard electric cable length is 25' with 6-Way Aluminum Die Cast Connector  (longer electric cables are provided for longer capacity pole trailers - Entire Assembly is Galvanized

Finish:
3 step Triple Hot Dipped Galvanized Finish
All Attaching parts are Painted before Assembly and Installed with Serviceable Fasteners
Rust Prohibitive Two-Part Epoxy Polyamide Primer
Two-Part Acrylic Polyurethane Topcoats
2" Red/White Reflective Tape


Options