Model

PTB81-9K

Capacity

• 10,500 lbs. GVWR - Calculated at 15% Weight Transfer to Tow Vehicle
• 7,500 lbs. Load Capacity

Dimensions

• Length Adjustments: 20’ / 25 ’ / 30’
• Cargo Bed Optional: 82”L x 39”W x 7”H
• Overall Width: 95”
• Bolster Height: 42”

Axles

• 9000 lbs. Single Dexter Straight Axle - (Optional Axles 10K, 12K & 15K)
• Oil Bath Hubs, 8 Studs
• 12 1/4” x 3 3/8” Electric Brakes All Wheels
• 4500 lbs. 6 Leaf Slipper Springs
• Adjustable Spring Pads for Wheel Alignment
• Reinforced Spring Hangers with 3” Structural C-Channel Crossmember
• (4) four - LT235/85R16 LR-E Tires, Capacity 2,778 lbs. each, Dual Wheel Application
• (4) four - 16” x 6” Wheels (8 Hole on 6 1/2" Bolt Circle)
• Pair - Mud Flaps

Pole Bolsters

• Front Bolster: 45”W Fixed (Mounted on Extendable Tongue)
• Center Bolster: 95”W Fixed 5” Double C-Channel Construction with 21” Stanchions
• Rear Bolster: 95”W Fixed 5” Double C-Channel Construction with 21” Stanchions
• Stanchions: (4) four - 21” Lever Lock, Sliding & Removable
• (4) four - Heavy Duty Ratchet Type Winch Binders with Breaker Bar
• (4) four - 15’ L x 4” W x 12000 lbs. Nylon Straps

Tongue & Hitch

• 7” x 3” x 1/4" Wall Extendable Tongue with Lubricated Steel Wear Pads
• 6-Position Adjustable Hitch Plate
• 2 1/2" Lunette Eye, 35000 lbs. Capacity
• 3/8” x 36”L Galvanized Safety Chains with Safety Hook and Anchor Shackle

A-Frame & Jack

• 7” Structural C-Channel A-Frame
• Fixed Binkley, Model 48000 Drop Leg Jack, 12,000 lb. Static Load Capacity

Main Frame

• 7” x 4” Tubular Steel Frame
• 7” x 4” Receiver Tube
• 7” x 4 “ Tubular Steel Crossmembers Under Rear Bolster
• 3” Structural C-Channel Crossmembers

Fenders

• Fabricated 1/8” Steel Diamond Tread Plate Fender Construction
• Reinforced with 3” Structural C-Channel at Front and Rear of Fender

Paint

• Trailer is Completely Sandblasted
• Seams are Sealed with Paintable Caulk
• Rust Prohibitive Two-Part Epoxy Polyamide Primer
• Two-Part Acrylic Polyurethane Topcoats (Standard Colors Black and White)
• All Attachments Painted before Assembly and Installed with Serviceable Fasteners
• 2” Red/White Reflective Tape on Both Sides of Trailer

12 Volt Wiring System

• ICC & DOT Approved Lights
• Sealed Beam Rubber Mounted Stop, Turn, Tail and Marker Lights
• S.O. Cable Wiring Loom, Clamped on 16” Centers with Rubber Lined Clamps
• Wiring Loom Terminated in Junction Boxes
• Connections Soldered and Sealed with Heat Shrink Tubing
• Stretch Coil Cord with Retainer on Extendible Tongue
• 32” Pigtail w/ 6-Way Aluminum Die Cast Plug, Terminated at Junction Box
• 6-Way Aluminum Die Cast Plug (Truck Side) in Rear Butt Tube for Light Bar Hook-Up
• Breakaway Kit with Sealed Lead Acid Battery and Trickle Charger