UP-5000 Underground Puller Tracks
UP5000T – Tracked Underground Puller
UNIT PERFORMANCE:
Rated Line Pull: 5000 lbs.
Line Speed : Approx. 2-3 MPH
Dimensions:
Overall Length – Approx. 116.5″L
Overall Width – Approx. 62.375″W
Overall Height – 113.625” (with Jib Stowed)
CTS-78R Chermack Rubber Tracks Carrier:
-Forged idlers, spring loaded forged tensioning idler and through hardened drive sprockets.
-Nachi 3B Compact Hydraulic with 45.2:1 gear ratio, open loop planetary drive motors with two speeds and internal parking brake.
DRUM:
Quantity: 1
Diameter: 20″
Inside Width: 18″
Core Diameter: 8-5/8″
REEL CAPACITY:
1500′ of 5/16″ Saturn 12 Pulling Line (Synthetic Rope)
LEVELWIND:
Automatic – Leadscrew design
POWER TRAIN/HYDRAULICS:
YANMAR 4TNV – 35 HP @ 3000 RPM – Industrial Diesel Power Unit Complete with: Radiator, Fan Guard, Radiator Hoses, Exhaust Muffler, Air Cleaner, Engine Support Legs, Steel Rail Skid, ML Control Panel, Safety Shutdown System, Throttle, Oil and Fuel Filters, SAE 5 Rear Housing, SAE 7.5″ Flywheel Owner’s Manual
Fuel Capacity – 18 Gallons
Full Hydrostatic Drive Pump
OPERATOR/SAFETY FEATURES:
Operator controls are located on the curbside of unit (ground controls)
Hydraulic Free-Wheeling Disconnect for cable Payout
(2) Grounding Lugs mounted front, each side
Payout Brake Assembly:
Overspin brake assembly equipped on drum for rope/cable Payout
MAIN FRAME:
7″ x 3″ Steel Tube Main Frame
5″ x 3″ Steel Tube cross members
*Rear Underground Fairlead Guide Assembly
*Dual Hydraulic cylinders hydraulically lower the fairlead assembly and raise for travel position.
*Fully Hydraulic slide out extension for positioning jib over duct work.
*Dual 10″ cascading rollers at end of jib
*Entire Jib is Hydraulically adjustable side to side
*Wireless Remote Control Including:
-Track Joysticks
-High/Low Range Track Speed
-Track Sensitivity Mode
-Line footage and Tension Readout
-Emergency Stop
-Drum Pay in/Pay Out
-Drum Speed Control
Transport Trailer: Brooks Model SLT 141 – 8KE Tilt-Deck Trailer
GVWR: 9,400
14′ Deck Length
60″ Tongue Length
102″ Overall Width
81″ Deck Width Between Fenders
16″ Low Profile Deck Height
8000# Dexter Torflex Axle
(2) two – 215/75R17.5 LR-H Tires
(2) two – 17.5″ x 6.75″ (8 Hole on 6 1/2″ Bolt Circle)
Spring Loaded Tilt Deck Latching System
12″ Tapered Entrance Ramp
6″ x 2″ Tubular Upper Tongue
5″ x 2″ Tubular Lower Tongue
2-1/2″ Lunette Eye mounted on adjustable hitch plate
6-Position Adjustable Hitch Plate
12,000# HD Dropleg Jack
7″ x 4″ x 3/8″ Angle Frame
3″ Channel Crossmembers
(4) Swiveling Ratchet Binders with 4” Wide Tie Down Straps and incorporated Tie down Chain and Hook
ICC & DOT Approved LED Lights
Sealed Beam Rubber Mounted Stop, Turn, Tail and Marker Lights
S.O. Cable Wiring Loom, Clamped on 16″ Centers with Rubber Lined Clamps
Wiring Loom Terminated in Junction Boxes
Connections Soldered and Sealed with Heat Shrink Tubing
Breakaway Kit, with Sealed lead Acid Battery & Trickle Charger
Trailer is Completely Steel Grit Blasted
Seams are Sealed with Paintable Caulk
Rust Prohibitive Two-Part Epoxy Polyamide Primer
Two-Part Acrylic Polyurethane Topcoats
All Attachments Painted before Assembly and Installed with Serviceable Fasteners
